Samsung SGH-600 / SGH-2100
Secret Codes
*#06# -> Show IMEI
*#9999# -> Show Software Version
*#0837# -> Show Software Version (instructions)
*#0001# -> Show Serial Parameters
*#9125# -> Activates the smiley when charging.
*#9998*228# -> Battery status (capacity, voltage, temperature)
*#9998*246# -> Program status
*#9998*289# -> Change Alarm Buzzer Frequency
*#9998*324# -> Debug screens
*#9998*364# -> Watchdog
*#9998*377# -> EEPROM Error Stack - Use side keys to select values. Cancel and ok.
*#9998*427# -> Trace Watchdog
*#9998*523# -> Change LCD contrast - Only with version G60RL01W
*#9998*544# -> Jig detect
*#9998*636# -> Memory status
*#9998*746# -> SIM File Size
*#9998*778# -> SIM Service Table
*#9998*785# -> RTK (Run Time Kernel) errors - if ok then phn is reset, info is put in memory error. *#9998*786# -> Run, Last UP, Last DOWN
*#9998*837# -> Software Version
*#9998*842# -> Test Vibrator - Flash the screenligth during 10 seconds and vibration activated.
*#9998*862# -> Vocoder Reg - Normal, Earphone or carkit can be selected
*#9998*872# -> Diag
*#9998*947# -> Reset On Fatal Error
*#9998*999# -> Last/Chk
*#9998*9266# -> Yann debug screen (=Debug Screens?)
*#9998*9999# -> Software version
*0001*s*f*t# -> Changes serial parameters (s=?, f=0,1, t=0,1) (incomplete)
*0002*?# -> unknown
*0003*?# -> unknown
SP-unlock SGH-600 and SGH 2100
*2767*3855# -> Full EEPROM Reset ( THIS CODE REMOVES SP-LOCK!! )
But also changes IMEI to 447967-89-400044-0, To restore your old IMEI use the IMEI program found on the software page.
*2767*2878# -> Custom EEEPROM Reset
These codes has been tested with version FLD_2C6 G60SB03X of Samsung SGH-600
Samsung 811
Jul, 08 2000 - 01:24
47*869#08#9
- unlock code / change roaming code / ID
SIEMENS S1 / S3 / S3 COM / S4
To view the software date and else with S3 com, S4, S4Power
press with SIM removed *#06# and left softkey.
To view some other stuff with S4Power
press with SIM removed *#06# and left softkey twice.
To view the software date with S3 com, S4, S4Power
press with SIM installed menu 98 and left softkey twice.
ACTIVATE MONITOR MODE
Siemens S1/S3
Menu, 9 (Phone Options), 7 (Phone Status), Left Display Button (left MENU key),
5553756, HangUp Button (Red HandSet key)
Siemens S3 COM/S4
Menu, 9 (Phone Options), 7 (Phone Status), Left Display Button
(left MENU key), 7684666, HangUp Button (Red HandSet key)
Note: Now Monitor should appear at the bottom of the Network Options menu.
MONITOR MODE
Pressing the right Display Button when in monitor mode will toggle into 1 and 2 modes
Pressing the right Display Button when in monitor mode will show a
list of the six cells with the strongest signals.
Test Mode Indicators: (* = only available when call in progress )
CH Channel Number
RX Signal Strength (dB)
N NCC (Colour Code)
B BCC (Colour Code)
CI Cell ID (in Hex)
C1+ How long before phone does forced hand over.(see RX and RXAM)
LAI Location Area Identity. Display Network ID code(42F010 = 240.01) and MSC
TXPWR Transmit Power (dB)
RXAM Receive signal strength cut-off point
TS* Time Slot Number
TA* Timing Advance. Distance from tower in Km X 2
PL* Power Level
SIEMENS S1
Here’s a trick to play Tetris, also known as Klotz on a Siemens S1.
Turn the phone on. Enter PIN. Before the telephone has logged in to the
your GSM net do the following steps.
1: Choose F 9 (function settings)
2: Choose send own number and push the right button for choose.
3: Push 9
USE 2 as < and 8 as > , rotate the klotz with 5 and drop with 4.
I have just heard from one of the programmers of the phone that Tetris
was in the phone during development, but it was removed before it was produced.
Apparantly someone has the patent on games in mobile phones and Siemens
didn’t want to pay the licensing fees. It was either in Menu F-9-9 or it’s not there at all.
Siemens C 25
Secret Codes
SP unlock *#0003*(secret code 8 digits)#
*#06# for checking the IMEI (International Mobile Equipment Identity)
Resets language to automatic selection : * # 0000 # then Green button
Pin Out
1- GND
2- SB
3- POWER
4- NC
5- TX
6- RX
7- CLOCK
8- DATA
9- GND MIC
10- HF MIC
11- AUDIO
12- GND AUDIO
Sagem MC959
Secret Codes
MC959
in main menu press * for hot-menu:
lcd, led, vibra, tests, imei, software versions, battery voltage
Type MENU - 5 - 1 - 1 - # to enter Engineering menu on SAGEM (RC-712, 721, 815 and 815 plus) phones.
Panasonic G500
IEMI:
To view IMEI number *#06#
——————————————————————————–
PINOUTS
1 - Ground
2 - TX_Audio
3 - Audio_Ground
4 - HF_ON (L=ON) -> L=H/F ON
5 - AOP_Sense <- Data Adaptor Select
6 - Serial_Up <- UART up (9600,33.8kbps)
7 - Serial_Down -> UART down
8 - External_Power <- POWER FOR CHARGING
9 - Ground
10 - RX_Audio
11 - Radio_Mute -> L=MUTE
12 - HF_Sense <- L=H/F MODE
13 - Reserved L=FLASH WRITE ENABLE
14 - Ignition <- H=ON
15 - Logic_Power -> H=HANDSET ON
16 - PAON -> Power Amplifier Control Signal.
Mitsubishi MT- D30
Secret Codes
Monitor mode: Hold C and press 379
Secret menu: Hold C and press 987
Version number: Hold C and press 597
Phase1 and 2 : Hold C and press 499
Warm start : Hold C and press 179
Instant turn off: Hold C and press 999
Unlock menu: Hold C and press 787090
Mitsubishi Trium
*#0000# to reset the phones menu-language to natural language, set initially by the distributor.
*#06# for checking the IMEI (International Mobile Equipment Identity)
hold * then 5806 - show software version
hold * then 5807 - a littel bit diffrent
hold * then 5472 - Testmode for datacable (it seems so)
hold * then 4329 - Activate and deactivate NETMONITOR
hold * then 621342 - Activate and deactivate another NETMONITOR
hold * then 3926 - shutdown
SP lock
You can turn around the lock routin by entering **04*PIN*PIN*PIN# now the secretcode change was applied and the software turns back to main menue. It works not on all triums, only on thos with older sofware versions.
SIEMENS S1 / S3 / S3 COM / S4
To view the software date and else with S3 com, S4, S4Power
press with SIM removed *#06# and left softkey.
To view some other stuff with S4Power
press with SIM removed *#06# and left softkey twice.
To view the software date with S3 com, S4, S4Power
press with SIM installed menu 98 and left softkey twice.
ACTIVATE MONITOR MODE
Siemens S1/S3
Menu, 9 (Phone Options), 7 (Phone Status), Left Display Button (left MENU key),
5553756, HangUp Button (Red HandSet key)
Siemens S3 COM/S4
Menu, 9 (Phone Options), 7 (Phone Status), Left Display Button
(left MENU key), 7684666, HangUp Button (Red HandSet key)
Note: Now Monitor should appear at the bottom of the Network Options menu.
MONITOR MODE
Pressing the right Display Button when in monitor mode will toggle into 1 and 2 modes
Pressing the right Display Button when in monitor mode will show a
list of the six cells with the strongest signals.
Test Mode Indicators: (* = only available when call in progress )
CH Channel Number
RX Signal Strength (dB)
N NCC (Colour Code)
B BCC (Colour Code)
CI Cell ID (in Hex)
C1+ How long before phone does forced hand over.(see RX and RXAM)
LAI Location Area Identity. Display Network ID code(42F010 = 240.01) and MSC
TXPWR Transmit Power (dB)
RXAM Receive signal strength cut-off point
TS* Time Slot Number
TA* Timing Advance. Distance from tower in Km X 2
PL* Power Level
SIEMENS S1
Here’s a trick to play Tetris, also known as Klotz on a Siemens S1.
Turn the phone on. Enter PIN. Before the telephone has logged in to the
your GSM net do the following steps.
1: Choose F 9 (function settings)
2: Choose send own number and push the right button for choose.
3: Push 9
USE 2 as < and 8 as > , rotate the klotz with 5 and drop with 4.
Coba pake: *3001#12345#
Ati2 jgn diubah2 setting CDMAnya, kalo salah kode bisa2 nggak dapet sinyal lagi lho!
gue pake *3001#12345# bisa remove operator logo hehehehehe, caranya pilih alpha tag, lalu kosongin aja atau ganti sesuai keinginan.
terus keluar dan ketik *#75681# dan nakal keluar "slot cycle .... "
Jika ponsel GSM kita mengenal kode "*#06" untuk mengecek nomor IMEI atau "*#0000# untuk mengetahui versi software, maka ponsel-ponsel CDMA pun memiliki kode-kode tersendiri.
Untuk mengetahui versi ponsel :
ketik "*#837# or "*#VER# berlaku untuk beberapa model.
Untuk Akses ke menu Rahasia :
ketik "*3001#12345#"
Untuk memunculkan Menu Net Monitor :
Ketik "*3001#12345#" tunggu sampai keluar menunya
Setelah itu pilih field "test"
Pilih "enable"
Restart ponsel anda
akan muncul menu baru yaitu net monitor guna mengetahui kondisi jaringan operator anda.
Untuk merubah Nama Operator :
Ketik "*3001#12345#" tunggu sampai keluar menunya
pilih "nam1"
pilih "alpha tag"
masukkan kata yang anda inginkan untuk menggantikan nama operator
untuk menghilangkn nama operator cukup tekan spasi
restart ponsel dengan menekan "*#75681#
maka nama operator kan berganti dengan nama pilihan anda.
0 comments:
Post a Comment
sabar ya, komentar anda akan kami moderasi terlebih dahulu. laporkan kepada kami apabila ada post yang masih berbentuk kiri ke kanan. nuhun